top of page

Polymeric Sand for Interlock in Ontario: When and How to Apply It

3 days ago
5 min read

Polymeric sand is a joint sand mixed with binders that harden after you wet it, locking interlocking pavers together and resisting weeds, ants and washout. It works well in Ontario, but only when it's installed on a completely dry surface, in above-freezing weather, with no rain in the forecast. Techniseal, for example, calls for temperatures above 0 °C for 48 hours after installation, no rain for 24 hours, and joints at least 4 cm (1.5 in.) deep. In London, that makes late spring through early fall the window, and mid-November is usually too late.


If your interlock joints washed out this year, this guide explains when to re-sand, how to do it properly and what to do if you have to wait until spring.


What Polymeric Sand Does


Interlocking pavers rely on the sand in their joints. The sand transfers loads between stones so they move together instead of shifting one by one. Regular joint sand works, but it washes out, lets weeds root, and gives ants an easy home.


Polymeric sand adds binders that activate with water. Once cured, the joint stays flexible enough to handle freeze-thaw movement, but firm enough to resist:


  • Washout from rain, downspouts and pressure washing

  • Weed seeds germinating in the joints

  • Ants tunnelling and piling sand on the surface

  • Sand being tracked into the house


It doesn't fix a failing base, though. If pavers are sinking, rocking or heaving, the problem is under the stones, not between them.


Manufacturer Rules That Matter in Ontario


Every brand has its own instructions, and you should follow the one on your bag. Two major manufacturers give a good picture of what's typical.



  • Temperature above 0 °C (32 °F) for 48 hours after installation

  • No rain in the forecast for the next 24 hours

  • A minimum joint depth of 4 cm (1.5 in.)

  • A dry surface and dry joints


The Alliance Gator installation guide says to install at 32 °F (0 °C) or above, on a dry surface. It also says to avoid rain within one hour on a drainage base, or within 24 hours on a non-drainage base, and notes that one of its rapid-set products is rain safe after 15 minutes.


The theme is clear: dry, above freezing, and a stable forecast.


Why Late Fall Is Risky in London


By mid-November in southwestern Ontario, nights regularly dip below freezing, mornings bring dew or frost, and rainy days are frequent. Even when the afternoon is mild, the pavers and the sand below may not be dry. If water reaches the sand before it cures, the binder can wash out or leave a haze on the stones. If it freezes before curing, the joint may crumble.


For most London properties, the safest window for polymeric sand runs from late spring into early fall, picking a stretch of dry days. If your patio needs work now, see the short-term options below.


How to Install Polymeric Sand Step by Step


  1. Check the forecast. Look for at least one to two dry days and temperatures that stay above freezing, matching your product's instructions.

  2. Clean out the joints. Remove old sand, weeds and debris to the depth the product requires. A joint scraper, a pressure washer on a low angle, or a joint-cleaning tool all work.

  3. Let everything dry completely. This is the most important step. Pavers and the bedding sand below must be dry. Damp joints cause early activation and haze.

  4. Repair the base if needed. Lift and reset any sunken or rocking pavers before sanding.

  5. Spread the sand. Pour it onto the surface and sweep it into the joints with a push broom.

  6. Compact. Run a plate compactor with a protective pad over the surface, or tap the pavers, to settle the sand. Add more sand and repeat until the joints are full to the level the instructions require.

  7. Clean the surface thoroughly. Sweep, then use a leaf blower to remove every grain from the paver faces. Leftover sand hardens into a haze.

  8. Activate with water. Mist the area as the instructions say. Don't flood it, because too much water washes out the binder.

  9. Let it cure. Keep foot traffic and vehicles off for the time the product specifies.


Wildflowers and weeds growing in the open joints between paving stones

Polymeric Sand vs. Regular Joint Sand


  • Weed resistance: polymeric is high, regular sand is low.

  • Washout resistance: polymeric is high, regular sand is low.

  • Installation: polymeric needs dry, warm weather and careful cleanup. Regular sand can go in almost anytime.

  • Repairs: polymeric is harder to remove when lifting stones. Regular sand is easy.

  • Haze risk: polymeric can haze if the surface isn't cleaned. Regular sand has none.

  • Best use: polymeric suits patios, walkways and driveways that see weeds and washout. Regular sand suits temporary repairs and some permeable systems.


For permeable pavers, check the manufacturer's spec. Many permeable systems use clear chip stone in the joints, not polymeric sand, so water can pass through.


Common Polymeric Sand Problems and Their Causes


  • White or grey haze on the pavers: sand left on the surface, or too much water during activation.

  • Soft or crumbly joints: not enough water, rain before curing, or freezing before curing.

  • Sand washing out: joints not filled deep enough, or heavy rain too soon.

  • Cracks along joints: a moving base, or joints too narrow or too shallow for the product.

  • Weeds still growing: joints not cleaned deep enough before sanding, or the sand didn't cure fully.


What to Do If Your Joints Need Help Before Winter


If your interlock has lost sand and the weather has turned:


  • Sweep in regular joint sand as a temporary fix. It keeps pavers locked through winter and can be cleaned out for polymeric in spring.

  • Redirect water. If a downspout is washing out joints, extend it onto the lawn.

  • Be gentle with snow removal. Use a plastic shovel blade or ask your contractor about rubber cutting edges on interlock.

  • Go easy on salt. Our guide to de-icing salt damage explains how salt affects pavers and joint sand.

  • Book spring work now. Re-sanding and base repairs are popular spring jobs.


When to Call a Pro


Re-sanding a small patio is a manageable DIY job if you follow the instructions exactly. Bring in a contractor when pavers are sunken, heaving or rocking, when edges are spreading, or when the area is a driveway. Those symptoms point to the base, and our post on interlock base prep that survives freeze-thaw explains what a proper base needs. If you're still choosing materials, our comparison of natural stone vs. concrete pavers can help.


FAQ


Can you put down polymeric sand in November in Ontario?


It's usually risky. Most products need dry joints, above-freezing temperatures for a day or two after installation, and no rain. Those conditions are rare in London by mid-November.


How deep should joints be for polymeric sand?


Follow your product's instructions. Techniseal SmartSand, for example, calls for a minimum joint depth of 4 cm (1.5 in.).


What happens if it rains on polymeric sand?


If rain hits before the sand cures, the binder can wash out or leave a haze on the pavers. Check your product's rain-safe time and the forecast before you start.


How do I remove polymeric haze from pavers?


Light haze can sometimes be removed with a haze remover made for pavers. Prevention is easier: blow every grain off the surface before wetting.


Does polymeric sand stop all weeds?


It greatly reduces weeds growing up through joints, but seeds can still land and sprout in dirt that collects on top. Sweeping regularly helps.


Plan Your Spring Interlock Repairs


SPM Landscape & Excavation has built and repaired hardscapes around London since 2006. We're WSIB covered and carry $1M in liability insurance. See our work in the photo gallery, call (519) 474-0008, email spmlandscape@gmail.com, or visit us at 791 Manchester Rd, London ON. We also supply gravel and base materials.


Comments


(519) 474-0008

©2022 by S.P.M Landscape

bottom of page